Legrand 861 Series Outlet Boxes for Wood Manuel d'utilisateur télécharger pdf

861 Series Outlet Boxes

for Wood & Raised Floors

INSTALLATION INSTRUCTIONS

Installation Instruction No.: 1 002 968R1 – Updated November 2005

Walker

electrical systems conform to and should be properly

grounded in compliance with requirements of the current National

Electrical Code or codes administered by local authorities.

All electrical products may present a possible shock or fire

hazard if improperly installed or used. Walker electrical products

may bear the mark as UL Listed and/or Classified and should

be installed in conformance with current local and/or the

National Electrical Code.

IMPORTANT: Please read all instructions

before beginning.

Products Covered: 861, 861QTC, 861AMDTC, 861AMDRTTC, & 861FFTC

Applications:

This unit is for wood floor and raised floor construction with:

• 3/4" [19.1mm] subflooring with carpet and padding or

• 3/4 [19.1mm] subflooring with 1/4" underlayment and tile or linoleum floor covering.

These requirements represent the minimum floor thickness to ensure enough cross section is available for the box to lock

into the subflooring.

• Suitable for use in air handling spaces in accordance with sec. 300-22(C) of the National Electrical Code.

BOX INSTALLATION

1. Determine the floor box location.

(Make sure the placement does not

interfere with obstructions below

such as floor joists, HVAC duct, light

fixtures, etc.) Drill a hole through

the flooring using a 4" [102mm] hole

saw (4 1/16" [104mm] actual).

2. For a flush installation in hardwood or

tile floors with the 895T or 896T series

covers - cut a 4 5/16" [109mm] diam-

eter, 1/8" [3.2mm] deep step in

the final floor covering.

3. Pull the nonmetallic sheathed cable or

armor clad cable up to and through

the 4" [102mm] hole.

NOTE: For air handling spaces allowed for that

application. See NEC 300-22(C). For

communications applications, type CMP

communication plenum cable is required

in raised floor plenums when wiring

methods as described in NEC article

300-22(C) are not followed.

4. Remove the appropriate 1/2" [12.7mm]

trade size knockout and attach a cable

connector to accommodate the wiring

system being used.

Attach the wiring system to the box.

To access the wiring cavity, open the

disposable cover cap and reseal after

use to avoid debris entry.

5. Orient the box to the desired rotation

and push into the hole. The box will

not turn once installed so make sure

the receptacle will be parallel or

perpendicular with any adjacent walls.

6. Use the disposable cover as a template

to trim around when installing carpet

or tile.

NOTE:

Refer to carpet/tile cutout

template when installing the

following catalog numbers:

861QTC, 861CMDTC,

861CMDRTTC, 861FFTC.

7. When wiring the final activation, remove

the disposable cover taking care not to

push the box through the opening.

1 2 3 4

Résumé du contenu

Page 1 - 861 Series Outlet Boxes

861 Series Outlet Boxesfor Wood & Raised Floors INSTALLATION INSTRUCTIONSInstallation Instruction No.: 1 002 968R1 – Updated November 2005Walke

Page 2

22. Attach trim flange to outlet boxusing (4) #6 x 3/8" flat head screws.3. Align gasket over receptacle and pressbead into flange. 4. Attach the

Page 3

3Point Keystone TabAway From Bezel.TracJack Blank(supplied)Foam Plug(supplied)TracJack (sold separately)Ortronics Series II Bezel andCommunication Jac

Page 4 - Carpet/Tile Cutout Template

Modèles reliés 861 | 861AMDTCGY | 861AMDTCBK | 861AMDTCVY | 861AMDTCAL | 861AMDTCBS | 861AMDTCAB | 861DB | 861FFTCGY | 861FFTCBK | 861FFTCVY | 861FFTCAL | 861FFTCBS | 861QTCGY | 861QTCBK | 861QTCVY | 861QTCAL | 861QTCBS |

Commentaires sur ces manuels

Pas de commentaire

Legrand 861 Series Outlet Boxes for Wood Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Legrand 861 Series Outlet Boxes for Wood. Legrand 861 Series Outlet Boxes for Wood User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 861 | 861AMDTCGY | 861AMDTCBK | 861AMDTCVY | 861AMDTCAL | 861AMDTCBS | 861AMDTCAB | 861DB | 861FFTCGY | 861FFTCBK | 861FFTCVY | 861FFTCAL | 861FFTCBS | 861QTCGY | 861QTCBK | 861QTCVY | 861QTCAL | 861QTCBS |

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Legrand 861 Series Outlet Boxes for Wood